Aquarius Dishwasher Prewash

This picture shows in detail the numbering of the pieces in the plate No. 1, we will identify the cut once iron.

To avoid confusion when assembling the frames of the boat, copy numbers of the previous image on the plate No. 1, with the help of a pencil.

Extract the pieces in the plate with the help of the cutter and carefully, they are very small and delicate parts.

With limatón or a piece of sandpaper, carefully go over the edges of the removed parts to eliminate grain raise.

Following the numerical order of the pieces, put no glue, frames B2, B3 and B4 on the false keel boat, part B1.

continue placing the frames on the false keel, respecting numerical order and not to be stuck yet, as shown in the picture.

Once assembled all frames on the false keel, placed Part B14, which serve to hold the assembly. As we can see, the B14 takes a lace piece to locate the projections fore and aft of the false keel, and the ends of the B7, the central frame and wider.

We put the set in the same position as shown in the photograph. Quick drying glue applied in the joint areas between the ribs and the false keel, also join the ends of the ribs with the part B14. Make sure that the pagamento not exceed the attachment point, for if eto occurs, the dye that apply to the whole structure would not be set in the stained area by the adhesive.

apply glue and set a piece B16 on each side of the bow of the false keel, as shown in the picture. Both pieces should be flush with the frame B2.

When the glue has dried, walnut stain applied to all frames and the false keel. For this operation, we can use any dye stain or wood into the water.

With a fine sanding block or a half-round limatón, polish the piece from the bow aft to bevel the edges of the frame.

This picture we can see the difference between the side that we sanded and it is intact.

We took a sheet of 1 x 3 mm and laying it on the ribs, as shown in the photograph, we see that sit on them properly.

Now, we sand from the stern toward the bow of the boat's base to get a good settlement of the liner. For curved and inaccessible areas, we use a half round limatón.

also found in this area of \u200b\u200bthe plates can be correctly seated. Remember that we sanded both sides of the pot equally.

After sanding the skeleton, we can begin to put the backing plates. The areas closest to the base of the frames have a brand that will serve as a starting point for placing the first strip of backing. It is advisable to sand and wet the sheets before putting them on the frames, to give elasticity and prevent breakage. Use fast-drying glue and set the first plate.

Cut leftover plate flush with the false keel fore and the last frame. We set another plate on the other side Hull at the same height as the first.

continue placing the sheets from the false keel and moving the first plate in place. As we move forward, you'll see that we must adjust the lengths and shapes of the plates for vompletar siding.

To close the small spaces that are left between the sheets, wedges and tuna we prepare as we did in the lining of the vessel.

sheathed mirror boat and then cut the excess of the plates, as shown in the picture.

We polish with sandpaper fine grain outside the boat. The wood must be smooth and without gaps between the sheets.

With a handsaw, cut the ribs that connect the pot to the base, following the cut marks that incorporate parts.

put the boat in a horizontal position and with the help of a block sander or a file, we match the sides of the boat, which will facilitate the settlement of the top of the gift.

sapelli We take two strips of 2 x 2 mm and sand it by all sides. The submerged in water for a while to gain elasticity, then, remove from water and dry it with a cloth. Apply glue and set one of the ribbons on the outside of the boat about 3 mm of the profile of the plate, as shown in the picture. The bar must extend from bow to stern, cut leftover strip flush with the bow and stern of the boat, place another strip on the other side.

With the boat in the position shown in the photograph and with the help of the cutter, cut the ends of the ribs until they go back 3 mm. This operation must be done very carefully and patiently not to damage the metal of the pot.

With strips of 2 x 3 mm assemble African walnut planking the bottom of the boat, as shown in the picture. Cut and adjust the slats required to do so.

recovered some African walnut strips of 2 x 5 mm left over from previous work to assemble the benches of the boat. The look at the positions shown in the picture. Inking the edges of the frames that are visible.

assembly at this stage of the boat painted or varnished

Once painted, will stick the wheel in the front of the boat in the position shown in the picture.

Following the stem, glue the piece needed African walnut strip of 2 x 3 mm to exceed the stern of the boat. Cut the remaining strip of mirror single boat, following the same inclination.

We found that gift is held properly on the boat and painted it black.

To set the gunwale, apply glue to the surfaces and center the piece on the boat. Pressed with fingers gunwale to suit the curve describing the boat. If necessary, reinforce the bonding glue inside the boat.

apply glue and set the rudder at the stern of the boat, so it is centered and flush with the bottom of the pot. Also paste the tiller in the position shown in the picture.