What Is The Minimum Thickness Of The Plastic?

Following the same processes as in the previous steps, build and trim will set the table ratchet on the other side of the helmet. table painted black trim and the five teams will stick on the table and against the hull fitting, a pair of tweezers. Distribute them as we see in the picture. will recover the plates left over from previous shows and extract five of them with a cutter. Then go over the outlines with a limatón and the paint. Glue the ribbon with the holes facing outwards, as shown in the picture. The bar should be flush with the top of the rubbing bands. With the drill and drill 1 mm in diameter, will open the holes that we have marked in the previous step. The holes should be perpendicular to the interns and full bar. After drilling the holes, lijaremos the bar to eliminate grain raise. will recover the two strips of sapelli of 2 x 15 x 105 mm cut in the previous phase. With them build tables for the club fitting ratchet. Present one of the slats against rubbing bands in the ship's side. If necessary, adjust the bar to the curve of the hull with a file. Then conducted with a punch marks to the distances in the image. follow the same steps to assemble and stick the pole table trim more from the other side of town. In this picture we can see how fitting is the table from another angle. Glue the ribbon to the holes on the outside, as shown in the picture. The bar should be flush with the upper edge of the rubbing bands, and will stick the two remaining teams. Glue three teams with fast-drying glue as shown in the photograph, in order to better position the bar table garnish. will recover the planks where the brackets and come stamped with the cutter, we extract five. We will review all the contours with a limatón, and paint with the same paint as the above. With the drill and drill 1 mm in diameter, will open the holes that we have marked in the previous step. The holes should be perpendicular to the interns and full bar. Once practiced drills, lijaremos the bar to eliminate grain raise. With the help of a ruler and an awl brands will chart that shows the image, 2 mm from the right side of the bar. is quite possible that the shape of the bar helmet does not fit properly. To adjust, as limaremos and give necessary curve as shown in the picture. will recover the two strips of sapelli of 2 x 15 x 135 mm cut at earlier stages. We used to build the tables lining the mainmast. Present one of the slats against rubbing bands, in the ship's side shown in the photograph. strip will take another 75 mm in length and the four teams that we extracted from the previous board. Prepare the table mizzenmast fitting for the other side of town, as we did in the previous steps. Glue four squadrons stationed on the table, distributed as shown in the photograph, with the help of forceps. It is quite possible that we should adjust the length of the brackets so they do not protrude from the fitting table. When given the case, adjust with a sanding block. extracted with a cutter eight squads of the plate which are punched. Then go over all the contours with a limatón, and red paint. is very important that the table is completely horizontal trim. It is quite possible that we have to force a little piece to fit the curve of the gunwale. Glue trim table set above the pockets of the stern, just below the gunwale on the side of the hull, as shown in the picture. As you can see the holes in the trim table are located near the outer side. With the drill and drill 1 mm in diameter perforated marks drawn in the previous step. The holes should be perpendicular to the interns and full bar. Once the drills, lijaremos the bar to remove the repel, and paint. We will one of the slats of 75 mm in length to set the table trim mizzen. With the help of a ruler or a punch, after showing marks ka image, 2 mm away from one long side of the bar. With a piece of fine grit, puliremos the strips until they are smooth and without grumbling. sapelli with strips of 2 x 15 x 300 mm going to build the tables lining. Cut two pieces of 105 mm, two 135 mm and two 75 mm long with the help of a saw, preferably, rib.

http://211060.guetbook.motigo.com